If the associated radiator set is isotropic, so will be the transmitter set. By default, an isotropic transmitter has vertical polarization. You can use the '''Polarization''' radio button to select one of the two options: '''Vertical''' or '''Horizontal'''. If the associated radiator set consists of '''Short Dipole''' or '''User Defined''' radiators, it is indicated in the transmitter property dialog. In the case of a short dipole radiator, you can set a value for the dipole current in Amperes. The radiation resistance of a short dipole of length ''dl'' is given by:
:<math> R_r = 80\pi^2 \left( \frac{dl}{\lambda_0} \right)^2 </math><!--[[File:eqngr6.png]]-->
The radiated power of a short dipole carrying a current I<sub>0</sub> is then given by:
:<math> P_{rad} = \frac{1}{2} R_r |I_0|^2 = 40\pi^2 |I_0|^2 \left( \frac{dl}{\lambda_0} \right)^2 </math><!--[[File:shortdipole.png]]-->
For isotropic and user defined radiators you can set the '''Input Power''' and '''Phase''' of a transmitter set in Watts and degrees, respectively. This can be accessed from the '''Transmitter Chain''' dialog, which will be described in detail in the next section. The radiation pattern of the associated radiator set is normalized and used in conjunction with the input power value to create a weighted distribution of transmitted rays. In certain cases like hybrid simulations, you may want to use the actual values of the far field to define the transmitter power rather than a normalized radiation pattern. Note that the pattern (.RAD) file contains the value of total radiated power in its header. In this case, check the box labeled '''"Calculate Power From Radiation Pattern"'''. This is calculated directly from the complex θ and φ components of the far field data by integrating them over the entire space (4π solid angle). Note that this option is available only when the radiator is of the User Defined type. When this box is checked, the transmitter chain button is grayed out. By default, an isotropic transmitter emanates rays uniformly in all directions at the angular resolution specified by the user. A transmitter with a user defined associated radiator may represent a highly directional radiation pattern with the main beam pointing in a certain direction. You can additionally force and limit the '''Angular Extents''' of rays to a certain solid angle around the transmitter. This is especially useful and computationally efficient when the transmitter is on one side of the scene, and all the scatterers and receivers are on the other side. In this case, there is no need to generate rays in all directions. To limit the angular extents of rays, define the Start and End values for both Theta (θ) and Phi (φ) angles. The value of the angular resolution of the rays can be changed from the Run Dialog as will be discussed later.
In a regular SBR simulation, you have a transmitter and one or more arrays of receivers in your scene. At the end of the simulation, you can visualize the coverage map of the transmitter over the receiver sets. A coverage map shows the total '''Received Power''' by each of the receivers and is visualized as a color-coded intensity plot. You can visualize the coverage maps of individual receiver sets. At the end of a SBR simulation, each Received Power Coverage Map is listed under the receiver set's name in the Navigation Tree. To display a coverage map, simply click on its entry in the Navigation Tree. The coverage map plot appears in the Main Window overlaid on the scene. A legend box on the right shows the color scale and units (dB). The 3-D coverage maps are displayed as horizontal confetti above the receivers. If the receivers are packed close to each other, you will see a continuous confetti map. If the receivers are far apart, you will see individual colored squares. You can also visualize coverage maps as colored 3-D cubes. This may be useful when you set up your receivers in a vertical arrangement or the scene has a highly uneven terrain. To change the type of coverage map visualization, open the receiver set's property dialog and select the desired option for '''Coverage Map: Confetti''' or '''Cube''' in the '''"Visualization Options"''' section of the dialog.
[[File:prop_run11_tn.png]] [[File:prop_run12_tn.png]]
Received power coverage map: (Left) confetti style, and (Right) cube style.